Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
Do you find yourself trying to locate info on Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably tough task. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open a wall to eliminate the old tub and place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have certified on your own for the work and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new tub and also do not require to change the setup of your previous supply of water pipes.
Your devices as well as product checklist need to consist of the following:
Getting ready for the Installation
First of all, the sustaining frame provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have actually been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, position the bathtub in the needed setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub up until the spirit level reads level.
To mount taps, fit the bottom of the outermost versatile tap port to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leaks and also tighten them if required. Fill up the bath tub and likewise examine the overflow outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the bathtub ought to wait until the tub has been made use of at least when as this will certainly resolve it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines are in area between the tap and also the sink. Secure the tap in position with the manufacturer given backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be linked to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can fracture fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about Tools You Need to Install a New Bathtub , I assumed sharing that piece of content was worth the trouble. In case you appreciated our blog post kindly do not forget to pass it around. Thank you for your time. Visit again soon.
Guaranteed fix? Call. Report this page